Putting in Chair Rail and Frieze Molding

Chair rail and frieze molding are two techniques to improve the design and magnificence of any space. Visually, these ornamental features incorporate harmony to your room’s décor. Implementing chair rail molding eases the vast scale and vacant feeling of huge rooms or substantial ceilings. Combine and match window surrounds, chair rails and friezes. The huge range of dimensions and designs obtainable makes it possible for you to develop a entire new appear. Putting in these ornamental accents can be completed by any do-it-yourselfer with a small scheduling and preparation.

Equipment and Supplies

Some of the equipment you will need involve:

Sponge or a cleanse cloth
Caulking gun
Miter box and observed or energy miter observed
Chalk line box and pencil
Polyurethane design adhesive
Mineral spirits

Some optional equipment and components you might look at practical: a putty knife, hammer, Elastomeric adhesive caulk, 6d or 8d finishing nails (to penetrate a substrate a minimal of ½” to ¾”, and more high-quality sandpaper.

Setting up Your Area

The most important step of including chair rail or friezes to any space is to plan the structure. Chair rails are ordinarily installed a third of the way up the wall from the flooring, about 32″-36″. Frieze moldings are normally installed under your crown molding or a couple of inches reduce to variety a border.

First, measure your space to identify how a lot of toes of molding you will need for your undertaking. Then incorporate ten% to that for miter squander. Divide the complete toes by the molding size. For illustration, if the molding arrives in eight foot lengths, then divide your complete by eight. If you want the sample repeats, you could possibly look at including additional size to your obtain. For moldings with repeats that are increased than six”, incorporate a different fifteen% to your complete size.

Make absolutely sure to retailer the molding in a dry, very well-ventilated location and Never ever retailer it outside.

Prior to Installation

You can paint or faux end the molding both before you put in it or following. If you select to end it before you put in it, you can generally touch it up later as needed. Depart the molding in the space wherever it will be installed for 48-72 hrs to make it possible for it to regulate to the temperature and humidity of the space. Clear all of the surfaces free of charge of filth and unfastened particles with a sponge or cleanse cloth. Make absolutely sure that all the surfaces are wholly dry before you put in your molding.

Mitering Corners

Positioning the molding in the miter box properly is the essential to effective mitered corners. Since chair rail and frieze moldings are flat, they really should be placed in the miter box so that the bedding edge of the molding lies versus the facet of the miter box opposite you. Reduce all miters and butt joints before you put in the molding. Then lay the molding in location all over the space to make absolutely sure that all the cuts and joints have been measured properly.

To miter the inside of corners, get started by using two items of the molding that you will use for your 1st corner. Acquire the “left” size and location it in the miter box as explained earlier mentioned. Reduce a forty five degree mitered corner. Your observed really should be pointed Left. Subsequent, do the same thing with the “suitable” size, modifying your slash to make it possible for for the continuity of the sample. Of system, in this scenario, your observed really should be pointed Proper. Place the two finishes jointly to check out your cuts. Are they a excellent in shape? Terrific. Subsequent we’ll chat about mitering the outside corners.

Now, get two items of molding that you will use for your 1st outside corner. Place the “left” size in the miter box and slash a forty five degree corner. This time your observed really should position Proper. Subsequent, you’ll location the “suitable” size into the box to make your slash, once more enabling for the continuity of the sample. You’ll slash the suitable miter with your observed pointing Left. Examine your cuts once more for a excellent in shape.

If the molding lengths do not span the entire size of the space, then you will need to “butt joint” two lengths jointly. The repeat sample on just about every size of molding will match accurately other than when you slash the molding so match the repeat sample to the slash items of molding. Lay the size of molding in the miter box as explained earlier mentioned and slash a straight edge.

Normal Installation Considerations

Now it is really time to put in your chair rail or frieze molding. First, mark the wall with a chalk line. Mark the best edge of your chair rail or the bottom edge of the frieze. Start out the set up behind a door or some other inconspicuous spot due to the fact the repeat sample will most probably not match at your previous joint.

Use a ¼” bead of adhesive together the best and bottom of the again of your molding and at the butt joint finishes. Use the adhesive to fill in any gaps as very well. Press the molding into location and utilize caulking to the edges. Clean the caulk with a putty knife. Wipe the surplus adhesive from the edges and cleanse them with mineral spirits. A single selection that you have is to safe the molding with finishing nails. You can get rid of them following the adhesive dries if you depart about ½” of the nail uncovered. Use elastomeric adhesive to fill in the nail holes, smoothing the surface area with a putty knife. Once the adhesive dries, you can evenly sand the tough edges and touch up the molding as needed.

Often Be Safe

Stick to excellent procedures when functioning with equipment. Stick to manufacturer’s directions with the use of adhesives, paint, stain or energy equipment. Dress in safety goggles when making use of energy equipment or hammers. Often use the suitable device for the position.

Now love the new appear of your space understanding that you established this magnificence and attractiveness you.


Post time: 12-16-2016